 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DS2761 High-Precision Li+ Battery Monitor www.maxim-ic.com FEATURES Lithium-Ion (Li+) Safety Circuit - Overvoltage Protection - Overcurrent/Short-Circuit Protection - Undervoltage Protection Zero Volt Battery Recovery Charge Available in Two Configurations: - Internal 25mW Sense Resistor - External User-Selectable Sense Resistor Current Measurement - 12-Bit Bidirectional Measurement - Internal Sense Resistor Configuration: 0.625mA LSB and 1.9A Dynamic Range - External Sense Resistor Configuration: 15.625mV LSB and 64mV Dynamic Range Current Accumulation: - Internal Sense Resistor: 0.25mAhr LSB - External Sense Resistor: 6.25mVhr LSB Voltage Measurement with 4.88mV Resolution Temperature Measurement Using Integrated Sensor with 0.125C Resolution System Power Management and Control Feature Support 32 Bytes of Lockable EEPROM 16 Bytes of General-Purpose SRAM Dallas 1-Wire(R) Interface with Unique 64-bit Device Address Low Power Consumption: - Active Current: 60mA typ, 90mA max - Sleep Current: 1mA typ, 2mA max PIN CONFIGURATION CC PLS DC SNS SNS SNS DQ IS2 1 2 3 2 4 5 6 7 8 16 15 14 13 12 11 10 9 VIN VDD PIO VSS VSS VSS PS IS1 1 2 3 SNS 4 A DQ IS2 IS1 PS PLS DC CC VIN SNS Probe VSS Probe B C D E VDD PIO VSS F DS2761 16-Pin TSSOP Package DS2761 Flip-Chip Packaging* Top View PIN DESCRIPTION - Charge Control Output - Discharge Control Output DQ - Data Input/Output PIO - Programmable I/O Pin PLS - Battery Pack Positive Terminal Input PS - Power Switch Sense Input VIN - Voltage-Sense Input VDD - Power-Supply Input (2.5V to 5.5V) VSS - Device Ground SNS - Sense Resistor Connection IS1 - Current-Sense Input IS2 - Current-Sense Input SNS Probe - Do Not Connect - Do Not Connect VSS Probe CC DC * Mechanical drawing for the 16-pin TSSOP and DS2761 flip-chip package can be found at: http://pdfserv.maxim-ic.com/arpdf/Packages/16tssop.pdf http://pdfserv.maxim-ic.com/arpdf/Packages/chips/2761x.pdf 1-Wire is a registered trademark of Dallas Semiconductor. 1 of 24 072303 DS2761 ORDERING INFORMATION PART DS2761AE DS2761BE DS2761AE/T&R DS2761BE/T&R DS2761AE-025 DS2761BE-025 DS2761AE-025/T&R DS2761BE-025/T&R DS2761AX-025/T&R DS2761BX-025/T&R DS2761AX/T&R DS2761BX/T&R MARKING D2761EA D2761EB D2761EA D2761EB 2761A25 2761B25 2761A25 2761B25 DS2761AR DS2761BR DS2761A DS2761B DESCRIPTION TSSOP, External Sense Resistor, 4.275V VOV TSSOP, External Sense Resistor, 4.35V VOV DS2761AE on Tape-and-Reel DS2761BE on Tape-and-Reel TSSOP, 25mW Sense Resistor, 4.275V VOV TSSOP, 25mW Sense Resistor, 4.35V VOV DS2761AE-025 in Tape-and-Reel DS2761BE-025 in Tape-and-Reel Flip-Chip, 25mW Sense Resistor, Tape-and-Reel, 4.275V VOV Flip-Chip, 25mW Sense Resistor, Tape-and-Reel, 4.35V VOV Flip-Chip, External Sense Resistor, Tape-and-Reel, 4.275V VOV Flip-Chip, External Sense Resistor, Tape-and-Reel, 4.35V VOV Note: Additional VOV options are available, contact Maxim/Dallas Semiconductor sales. DESCRIPTION The DS2761 high-precision Li+ battery monitor is a data-acquisition, information-storage, and safetyprotection device tailored for cost-sensitive battery pack applications. This low-power device integrates precise temperature, voltage, and current measurement, nonvolatile (NV) data storage, and Li+ protection into the small footprint of either a TSSOP package or flip-chip package. The DS2761 is a key component in applications including remaining capacity estimation, safety monitoring, and battery-specific data storage. Through its 1-Wire interface, the DS2761 gives the host system read/write access to status and control registers, instrumentation registers, and general-purpose data storage. Each device has a unique factoryprogrammed 64-bit net address that allows it to be individually addressed by the host system, supporting multibattery operation. The DS2761 is capable of performing temperature, voltage, and current measurement to a resolution sufficient to support process monitoring applications such as battery charge control, remaining capacity estimation, and safety monitoring. Temperature is measured using an on-chip sensor, eliminating the need for a separate thermistor. Bidirectional current measurement and accumulation are accomplished using either an internal 25mW sense resistor or an external device. The DS2761 also features a programmable I/O pin that allows the host system to sense and control other electronics in the pack, including switches, vibration motors, speakers, and LEDs. Three types of memory are provided on the DS2761 for battery information storage: EEPROM, lockable EEPROM, and SRAM. EEPROM memory saves important battery data in true NV memory that is unaffected by severe battery depletion, accidental shorts, or ESD events. Lockable EEPROM becomes ROM when locked to provide additional security for unchanging battery data. SRAM provides inexpensive storage for temporary data. 2 of 24 DS2761 Figure 1. BLOCK DIAGRAM DQ 1-WIRE INTERFACE AND ADDRESS THERMAL SENSE VOLTAGE REFERENCE MUX ADC REGISTERS AND USER MEMORY LOCKABLE EEPROM SRAM TEMPERATURE VOLTAGE CURRENT ACCUM. CURRENT STATUS / CONTROL LI-ION PROTECTION TIMEBASE PIO CC DC VIN IS1 IS2 PLS PS + - INTERNAL SENSE RESISTOR CONFIGURATION ONLY 25mW SNS CHIP GROUND VSS IS2 IS1 TEST CURRENT AND RECOVERY CHARGE DETAIL IRC PLS VDD ITST ITST VSS 3 of 24 DS2761 Table 1. DETAILED PIN DESCRIPTION SYMBOL CC DC TSSOP 1 3 7 FLIP CHIP C1 B2 B4 DESCRIPTION Charge Protection Control Output. Controls an external p-channel high-side charge protection FET. Discharge Protection Control Output. Controls an external p-channel high-side discharge protection FET. Data Input/Out. 1-Wire data line. Open-drain output driver. Connect this pin to the DATA terminal of the battery pack. Pin has an internal 1mA pull-down for sensing disconnection. Programmable I/O Pin. Used to control and monitor user-defined external circuitry. Open drain to VSS. Battery Pack Positive Terminal Input. The DS2761 monitors the pack plus terminal through PLS to detect overcurrent and overload conditions, as well as the presence of a charge source. Additionally, a charge path to recover a deeply depleted cell is provided from PLS to VDD. In sleep mode (with SWEN = 0), any capacitance or voltage source connected to PLS is discharged internally to VSS through 200mA (nominal) to assure reliable detection of a valid charge source. For details of other internal connections to PLS and associated conditions see the Li+ Protection Circuitry section. Power Switch Sense Input. The device wakes up from Sleep Mode when it senses the closure of a switch to VSS on this pin. Pin has an internal 1mA pull-up to VDD. Voltage Sense Input. The voltage of the Li+ cell is monitored via this input pin. This pin has a weak pullup to VDD. Power Supply Input. Connect to the positive terminal of the Li+ cell through a decoupling network. Device Ground. Connect directly to the negative terminal of the Li+ cell. For the external sense resistor configuration, connect the sense resistor between VSS and SNS. Sense Resistor Connection. Connect to the negative terminal of the battery pack. In the internal sense resistor configuration, the sense resistor is connected between VSS and SNS. Current Sense Input. This pin is internally connected to VSS through a 4.7kW resistor. Connect a 0.1mF capacitor between IS1 and IS2 to complete a low-pass input filter. Current Sense Input. This pin is internally connected to SNS through a 4.7kW resistor. Do Not Connect. Do Not Connect. DQ PIO PLS 14 2 E2 B1 PS 10 E4 VIN VDD VSS SNS 16 15 13,14, 15 4,5,6 D1 E1 F3 A3 IS1 9 D4 IS2 SNS Probe VSS Probe 8 N/A N/A C4 C2 D2 4 of 24 DS2761 Figure 2. APPLICATION EXAMPLE 102 x 2 PACK+ BAT+ 1kW 1kW DS2761 CC PLS DC SNS SNS SNS DQ IS2 VIN VDD PIO VSS VSS VSS PS IS1 104 1kW 150W 150W 104 150W DATA 102 PS 4.7kW PACK(1) RSNS BAT- RSNS-INT SNS 4.7KW (2) VSS 4.7KW RKS IS2 RKS IS1 voltage sense DS2761 1) RSNS is present for external sense resistor configurations only. 2) RSNS-INT is present for internal sense resistor configurations only. 5 of 24 DS2761 POWER MODES The DS2761 has two power modes: active and sleep. While in active mode, the DS2761 continually measures current, voltage, and temperature to provide data to the host system and to support current accumulation and Li+ safety monitoring. In sleep mode, the DS2761 ceases these activities. The DS2761 enters sleep mode when any of the following conditions occurs: The PMOD bit in the Status Register has been set to 1 and the DQ line is low for longer than 2s (pack disconnection) The voltage on VIN drops below undervoltage threshold VUV for tUVD (cell depletion) The pack is disabled through the issuance of a SWAP command (SWEN bit = 1) The DS2761 returns to active mode when any of the following occurs: The PMOD bit has been set to 1 and the SWEN bit is set to 0 and the DQ line is pulled high (pack connection) The PS pin is pulled low (power switch) The voltage on PLS becomes greater than the voltage on VIN (charger connection) with the SWEN bit set to 0 The pack is enabled through the issuance of a SWAP command (SWEN bit = 1) The DS2761 defaults to sleep mode when power is first applied. Li+ PROTECTION CIRCUITRY During active mode, the DS2761 constantly monitors cell voltage and current to protect the battery from overcharge (overvoltage), overdischarge (undervoltage), and excessive charge and discharge currents (overcurrent, short circuit). Conditions and DS2761 responses are described in the sections below and summarized in Table 2 and Figure 3. Table 2. Li+ PROTECTION CONDITIONS AND DS2761 RESPONSES CONDITION NAME Overvoltage Undervoltage Overcurrent, Charge Overcurrent, Discharge Short Circuit ACTIVATION THRESHOLD DELAY RESPONSE VIN > VOV tOVD CC high VIN < VUV VIS > VOC VIS < -VOC(2) VSNS > VSC (2) tUVD tOCD tOCD tSCD CC , DC high, Sleep Mode CC , DC high DC high DC high RELEASE THRESHOLD VIN < VCE, or VIS -2mV VPLS > VDD (1) (charger connected) VPLS < VDD - VTP (3) VPLS > VDD - VTP (4) VPLS > VDD - VTP (4) VIS = VIS1 - VIS2. Logic high = VPLS for CC and VDD for DC . All voltages are with respect to VSS. ISNS references current delivered from pin SNS. 1) If VDD < 2.2V, release is delayed until the recovery charge current (IRC) passed from PLS to VDD charges the battery and allows VDD to exceed 2.2V. 2) For the internal sense resistor configuration, the overcurrent thresholds are expressed in terms of current: ISNS > IOC for charge direction and ISNS < -IOC for discharge direction 3) With test current ITST flowing from PLS to VSS (pulldown on PLS) 4) With test current ITST flowing from VDD to PLS (pullup on PLS) Overvoltage. If the cell voltage on VIN exceeds the overvoltage threshold, VOV, for a period longer than overvoltage delay, tOVD, the DS2761 shuts off the external charge FET and sets the OV flag in the protection register. When the cell voltage falls below charge enable threshold VCE, the DS2761 turns the 6 of 24 DS2761 charge FET back on (unless another protection condition prevents it). Discharging remains enabled during overvoltage, and the DS2761 re-enables the charge FET before VIN < VCE if a discharge current of -80mA (VIS -2mV) or less is detected. Undervoltage. If the voltage of the cell drops below undervoltage threshold VUV for a period longer than undervoltage delay tUVD, the DS2761 shuts off the charge and discharge FETs, sets the UV flag in the protection register, and enters sleep mode. The DS2761 provides a current-limited recovery charge path from PLS to VDD to gently charge severely depleted cells during sleep mode. Overcurrent, Charge Direction. The voltage difference between the IS1 pin and the IS2 pin (VIS = VIS1 VIS2) is the filtered voltage drop across the current-sense resistor. If VIS exceeds overcurrent threshold VOC for a period longer than overcurrent delay tOCD, the DS2761 shuts off both external FETs and sets the COC flag in the protection register. The charge current path is not re-established until the voltage on the PLS pin drops below VDD - VTP. The DS2761 provides a test current of value ITST from PLS to VSS to pull PLS down in order to detect the removal of the offending charge current source. Overcurrent, Discharge Direction. If VIS is less than -VOC for a period longer than tOCD, the DS2761 shuts off the external discharge FET and sets the DOC flag in the protection register. The discharge current path is not re-established until the voltage on PLS rises above VDD - VTP. The DS2761 provides a test current of value ITST from VDD to PLS to pull PLS up in order to detect the removal of the offending low-impedance load. Short Circuit. If the voltage on the SNS pin with respect to VSS exceeds short-circuit threshold VSC for a period longer than short-circuit delay tSCD, the DS2761 shuts off the external discharge FET and sets the DOC flag in the protection register. The discharge current path is not re-established until the voltage on PLS rises above VDD - VTP. The DS2761 provides a test current of value ITST from VDD to PLS to pull PLS up in order to detect the removal of the short circuit. Figure 3. Li+ PROTECTION CIRCUITRY EXAMPLE WAVEFORMS VCELL CHARGE VIS DISCHARGE (1) CC tOVD tOVD tOCD VOV VCE VUV VOC 0 -VOC -VSC VPLS VSS tUVD VDD VSS ACTIVE INACTIVE DC SLEEP MODE tSCD tOCD (1) To allow the device to react quickly to short circuits, detection occurs on the SNS pin rather than on the filtered IS1 and IS2 pins. The actual short-circuit detect condition is VSNS > VSC. 7 of 24 DS2761 Summary. All of the protection conditions described above are OR'ed together to affect the CC and DC outputs. DC = (Undervoltage) or (Overcurrent, Either Direction) or (Short Circuit) or (Protection Register Bit DE = 0) or (Sleep Mode) CC = (Overvoltage) or (Undervoltage) or (Overcurrent, Charge Direction) or (Protection Register bit CE = 0) or (Sleep Mode) CURRENT MEASUREMENT In the active mode of operation, the DS2761 continually measures the current flow into and out of the battery by measuring the voltage drop across a current-sense resistor. The DS2761 is available in two configurations: 1) internal 25mW current-sense resistor, and 2) external user-selectable sense resistor. In either configuration, the DS2761 considers the voltage difference between pins IS1 and IS2 (VIS = VIS1 VIS2) to be the filtered voltage drop across the sense resistor. A positive VIS value indicates current is flowing into the battery (charging), while a negative VIS value indicates current is flowing out of the battery (discharging). VIS is measured with a signed resolution of 12-bits. The current register is updated in two's-complement format every 88ms (128/fsample) with an average of 128 readings. Currents outside the range of the register are reported at the limit of the range. The format of the current register is shown in Figure 4. For the internal sense resistor configuration, the DS2761 maintains the current register in units of amps, with a resolution of 0.625mA and full-scale range of no less than 1.9A (see Note 7 on IFS spec for more details). The DS2761 automatically compensates for internal sense resistor process variations and temperature effects when reporting current. For the external sense resistor configuration, the DS2761 writes the measured VIS voltage to the current register, with a resolution of 15.625mV and a full-scale range of 64mV. Figure 4. CURRENT REGISTER FORMAT MSB--Address 0E S MSb 211 210 29 28 27 26 25 LSb 24 MSb 23 LSB--Address 0F 22 21 20 X X X LSb Units: 0.625mA for Internal Sense Resistor 15.625mV for External Sense Resistor CURRENT ACCUMULATOR The current accumulator facilitates remaining capacity estimation by tracking the net current flow into and out of the battery. Current flow into the battery increments the current accumulator while current flow out of the battery decrements it. Data is maintained in the current accumulator in two's-complement format. The format of the current accumulator is shown in Figure 5. 8 of 24 DS2761 When the internal sense resistor is used, the DS2761 maintains the current accumulator in units of amphours, with a resolution of 0.25mAhrs and full-scale range of 8.2Ahrs. When using an external sense resistor, the DS2761 maintains the current accumulator in units of volt-hours, with a resolution of 6.25mVhrs and a full scale range of 205mVhrs. The current accumulator is a read/write register that can be altered by the host system as needed. Figure 5. CURRENT ACCUMULATOR FORMAT MSB--Address 10 S MSb 214 213 212 211 210 29 28 LSb 27 MSb 26 LSB--Address 11 25 24 23 22 21 20 LSb Units: 0.25mAhrs for Internal Sense Resistor 6.25mVhrs for External Sense Resistor CURRENT OFFSET COMPENSATION Current measurement and current accumulation are both internally compensated for offset on a continual basis minimizing error resulting from variations in device temperature and voltage. Additionally, a constant bias can be utilized to alter any other sources of offset. This bias resides in EEPROM address 33h in two's-complement format and is subtracted from each current measurement. The current offset bias is applied to both the internal and external sense resistor configurations. The factory default for the current offset bias is a value of 0. Figure 6. CURRENT OFFSET BIAS Address 33 S MSb 26 25 24 23 22 21 20 LSb Units: 0.625mA for Internal Sense Resistor 15.625mV for External Sense Resistor VOLTAGE MEASUREMENT The DS2761 continually measures the voltage between pins VIN and VSS over a range of 0 to 4.75V. The voltage register is updated in two's-complement format every 3.4ms with a resolution of 4.88mV. Voltages above the maximum register value are reported as the maximum value. The voltage register format is shown in Figure 7. 9 of 24 DS2761 Figure 7. VOLTAGE REGISTER FORMAT MSB--Address 0C S MSb 29 28 27 26 25 24 23 LSb 22 MSb 21 LSB--Address 0D 20 X X X X X LSb Units: 4.88mV TEMPERATURE MEASUREMENT The DS2761 uses an integrated temperature sensor to continually measure battery temperature. Temperature measurements are placed in the temperature register every 220ms in two's-complement format with a resolution of 0.125C over a range of 127C. The temperature register format is shown in Figure 8. Figure 8. TEMPERATURE REGISTER FORMAT MSB--Address 18 S MSb 29 28 27 26 25 24 23 LSb 22 MSb 21 LSB--Address 19 20 X X X X X LSb Units: 0.125C PROGRAMMABLE I/O To use the PIO pin as an output, write the desired output value to the PIO bit in the special feature register. Writing a 0 to the PIO bit enables the PIO output driver, pulling the PIO pin to VSS. Writing a 1 to the PIO bit disables the output driver, allowing the PIO pin to be pulled high or used as an input. To sense the value on the PIO pin, read the PIO bit. The DS2761 turns off the PIO output driver and sets the PIO bit high when in sleep mode or when DQ is low for more than 2s, regardless of the state of the PMOD bit. POWER SWITCH INPUT The DS2761 provides a power control function that uses the discharge protection FET to gate battery power to the system. The PS pin, internally pulled to VDD through a 1mA current source, is continuously monitored for a low-impedance connection to VSS. If the DS2761 is in sleep mode, the detection of a low on the PS pin causes the device to transition into active mode, turning on the discharge FET. If the DS2761 is already in active mode, activity on PS has no effect other than the latching of its logic low level in the PS bit in the special feature register. The reading of a 0 in the PS bit should be immediately followed by writing a 1 to the PS bit to ensure that a subsequent low forced on the PS pin is latched into the PS bit. 10 of 24 DS2761 MEMORY The DS2761 has a 256-byte linear address space with registers for instrumentation, status, and control in the lower 32 bytes, with lockable EEPROM and SRAM memory occupying portions of the remaining address space. All EEPROM and SRAM memory is general purpose except addresses 30h, 31h, and 33h, which should be written with the default values for the protection register, status register, and current offset register, respectively. When the MSB of any two-byte register is read, both the MSB and LSB are latched and held for the duration of the read data command to prevent updates during the read and ensure synchronization between the two register bytes. For consistent results, always read the MSB and the LSB of a two-byte register during the same read data command sequence. EEPROM memory is shadowed by RAM to eliminate programming delays between writes and to allow the data to be verified by the host system before being copied to EEPROM. All reads and writes to/from EEPROM memory actually access the shadow RAM. In unlocked EEPROM blocks, the write data command updates shadow RAM. In locked EEPROM blocks, the write data command is ignored. The copy data command copies the contents of shadow RAM to EEPROM in an unlocked block of EEPROM but has no effect on locked blocks. The recall data command copies the contents of a block of EEPROM to shadow RAM regardless of whether the block is locked or not. Table 3. MEMORY MAP ADDRESS (HEX) 00 01 02-06 07 08 09-0B 0C 0D 0E 0F 10 11 12-17 18 19 1A-1F 20-2F 30-3F 40-7F 80-8F 90-FF DESCRIPTION Protection Register Status Register Reserved EEPROM Register Special Feature Register Reserved Voltage Register MSB Voltage Register LSB Current Register MSB Current Register LSB Accumulated Current Register MSB Accumulated Current Register LSB Reserved Temperature Register MSB Temperature Register LSB Reserved EEPROM, block 0 EEPROM, block 1 Reserved SRAM Reserved READ/WRITE R/W R R/W R/W R R R R R/W R/W R R R/W* R/W* R/W * Each EEPROM block is read/write until locked by the LOCK command, after which it is read-only. 11 of 24 DS2761 PROTECTION REGISTER The protection register consists of flags that indicate protection circuit status and switches that give conditional control over the charging and discharging paths. Bits OV, UV, COC, and DOC are set when corresponding protection conditions occur and remain set until cleared by the host system. The default values of the CE and DE bits of the protection register are stored in lockable EEPROM in the corresponding bits in address 30h. A recall data command for EEPROM block 1 recalls the default values into CE and DE. The format of the protection register is shown in Figure 9. The function of each bit is described in detail in the following paragraphs. Figure 9. PROTECTION REGISTER FORMAT Address 00 Bit 7 OV Bit 6 UV Bit 5 COC Bit 4 DOC Bit 3 Bit 2 Bit 1 Bit 0 CC DC CE DE OV--Overvoltage Flag. When set to 1, this bit indicates the battery pack has experienced an overvoltage condition. This bit must be reset by the host system. UV--Undervoltage Flag. When set to 1, this bit indicates the battery pack has experienced an undervoltage condition. This bit must be reset by the host system. COC--Charge Overcurrent Flag. When set to 1, this bit indicates the battery pack has experienced a charge-direction overcurrent condition. This bit must be reset by the host system. DOC--Discharge Overcurrent Flag. When set to 1, this bit indicates the battery pack has experienced a discharge-direction overcurrent condition. This bit must be reset by the host system. CC -- CC Pin Mirror. This read-only bit mirrors the state of the CC output pin. DC -- DC Pin Mirror. This read-only bit mirrors the state of the DC output pin. CE--Charge Enable. Writing a 0 to this bit disables charging ( CC output high, external charge FET off) regardless of cell or pack conditions. Writing a 1 to this bit enables charging, subject to override by the presence of any protection conditions. The DS2761 automatically sets this bit to 1 when it transitions from sleep mode to active mode. DE--Discharge Enable. Writing a 0 to this bit disables discharging ( DC output high, external discharge FET off) regardless of cell or pack conditions. Writing a 1 to this bit enables discharging, subject to override by the presence of any protection conditions. The DS2761 automatically sets this bit to 1 when it transitions from sleep mode to active mode. STATUS REGISTER The default values for the status register bits are stored in lockable EEPROM in the corresponding bits of address 31h. A recall data command for EEPROM block 1 recalls the default values into the status register bits. The format of the status register is shown in Figure 10. The function of each bit is described in detail in the following paragraphs. 12 of 24 DS2761 Figure 10. STATUS REGISTER FORMAT Address 01 Bit 7 X Bit 6 X Bit 5 Bit 4 Bit 3 Bit 2 X Bit 1 X Bit 0 X PMOD RNAOP SWEN PMOD--Sleep Mode Enable. A value of 1 in this bit enables the DS2761 to enter sleep mode when the DQ line goes low for greater than 2s and to leave sleep mode when the DQ line goes high. A value of 0 disables DQ-related transitions into and out of sleep mode. This bit is read-only. The desired default value should be set in bit 5 of address 31h. The factory default is 0. RNAOP--Read Net Address Opcode. A value of 0 in this bit sets the opcode for the read net address command to 33h, while a 1 sets the opcode to 39h. This bit is read-only. The desired default value should be set in bit 4 of address 31h. The factory default is 0. SWEN--SWAP Command Enable. A value of 1 in this bit location enables the recognition of a SWAP command. If set to 0, SWAP commands are ignored. The desired default value should be set in bit 3 of address 31h. This bit is read-only. The factory default is 0. X--Reserved Bits. EEPROM REGISTER The format of the EEPROM register is shown in Figure 11. The function of each bit is described in detail in the following paragraphs. Figure 11. EEPROM REGISTER FORMAT Address 07 Bit 7 EEC Bit 6 LOCK Bit 5 X Bit 4 X Bit 3 X Bit 2 X Bit 1 BL1 Bit 0 BL0 EEC--EEPROM Copy Flag. A 1 in this read-only bit indicates that a copy data command is in progress. While this bit is high, writes to EEPROM addresses are ignored. A 0 in this bit indicates that data may be written to unlocked EEPROM blocks. LOCK--EEPROM Lock Enable. When this bit is 0, the lock command is ignored. Writing a 1 to this bit enables the lock command. After the lock command is executed, the LOCK bit is reset to 0. The factory default is 0. BL1--EEPROM Block 1 Lock Flag. A 1 in this read-only bit indicates that EEPROM block 1 (addresses 30 to 3F) is locked (read-only) while a 0 indicates block 1 is unlocked (read/write). BL0--EEPROM Block 0 Lock Flag. A 1 in this read-only bit indicates that EEPROM block 0 (addresses 20 to 2F) is locked (read-only) while a 0 indicates block 0 is unlocked (read/write). X--Reserved Bits. 13 of 24 DS2761 SPECIAL FEATURE REGISTER The format of the special feature register is shown in Figure 12. The function of each bit is described in detail in the following paragraphs. Figure 12. SPECIAL FEATURE REGISTER FORMAT Address 08 Bit 7 PS Bit 6 PIO Bit 5 MSTR Bit 4 X Bit 3 X Bit 2 X Bit 1 X Bit 0 X PS -- PS Pin Latch. This bit latches a low state on the PS pin, and is cleared only by writing a 1 to this location. Writing this bit to a 1 immediately upon reading of a 0 value is recommended. PIO--PIO Pin Sense and Control. See the Programmable I/O section for details on this read/write bit. MSTR--SWAP Master Status Bit. This bit indicates whether a device has been selected through the SWAP command. Selection of this device through the SWAP command and the appropriate net address results in setting this bit, indicating that this device is the master. A 0 signifies that this device is not the master. X--Reserved Bits. 1-WIRE BUS SYSTEM The 1-Wire bus is a system that has a single bus master and one or more slaves. A multidrop bus is a 1Wire bus with multiple slaves. A single-drop bus has only one slave device. In all instances, the DS2761 is a slave device. The bus master is typically a microprocessor in the host system. The discussion of this bus system consists of four topics: 64-bit net address, hardware configuration, transaction sequence, and 1-Wire signaling. 64-BIT NET ADDRESS Each DS2761 has a unique, factory-programmed 1-Wire net address that is 64 bits in length. The first eight bits are the 1-Wire family code (30h for DS2761). The next 48 bits are a unique serial number. The last eight bits are a cyclic redundancy check (CRC) of the first 56 bits (see Figure 13). The 64-bit net address and the 1-Wire I/O circuitry built into the device enable the DS2761 to communicate through the 1-Wire protocol detailed in the 1-Wire Bus System section of this data sheet. Figure 13. 1-WIRE NET ADDRESS FORMAT 8-BIT CRC MSb 48-BIT SERIAL NUMBER 8-BIT FAMILY CODE (30H) LSb CRC GENERATION The DS2761 has an 8-bit CRC stored in the most significant byte of its 1-Wire net address. To ensure error-free transmission of the address, the host system can compute a CRC value from the first 56 bits of the address and compare it to the CRC from the DS2761. The host system is responsible for verifying the CRC value and taking action as a result. The DS2761 does not compare CRC values and does not prevent 14 of 24 DS2761 a command sequence from proceeding as a result of a CRC mismatch. Proper use of the CRC can result in a communication channel with a very high level of integrity. The CRC can be generated by the host using a circuit consisting of a shift register and XOR gates as shown in Figure 10, or it can be generated in software. Additional information about the Dallas 1-Wire CRC is available in Application Note 27, Understanding and Using Cyclic Redundancy Checks with Dallas Semiconductor Touch Memory Products. (This application not can be found on the Maxim/Dallas Semiconductor website at www.maxim-ic.com). In the circuit in Figure 14, the shift register bits are initialized to 0. Then, starting with the least significant bit of the family code, one bit at a time is shifted in. After the 8th bit of the family code has been entered, then the serial number is entered. After the 48th bit of the serial number has been entered, the shift register contains the CRC value. Figure 14. 1-WIRE CRC GENERATION BLOCK DIAGRAM INPUT MSb XOR XOR LSb XOR HARDWARE CONFIGURATION Because the 1-Wire bus has only a single line, it is important that each device on the bus be able to drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must connect to the bus with open-drain or tri-state output drivers. The DS2761 used an open-drain output driver as part of the bidirectional interface circuitry shown in Figure 15. If a bidirectional pin is not available on the bus master, separate output and input pins can be connected together. The 1-Wire bus must have a pullup resistor at the bus-master end of the bus. For short line lengths, the value of this resistor should be approximately 5kW. The idle state for the 1-Wire bus is high. If, for any reason, a bus transaction must be suspended, the bus must be left in the idle state in order to properly resume the transaction later. If the bus is left low for more than 120ms, slave devices on the bus begin to interpret the low period as a reset pulse, effectively terminating the transaction. Figure 15. 1-WIRE BUS INTERFACE CIRCUITRY BUS MASTER Vpullup (2.0V to 5.5V) 4.7kW Rx 1mA (typ) Rx = RECEIVE Tx = TRANSMIT 15 of 24 DS2761 1-WIRE PORT Rx Tx Tx 100W MOSFET DS2761 TRANSACTION SEQUENCE The protocol for accessing the DS2761 through the 1-Wire port is as follows: Initialization Net Address Command Function Command Transaction/Data The sections that follow describe each of these steps in detail. All transactions of the 1-Wire bus begin with an initialization sequence consisting of a reset pulse transmitted by the bus master followed by a presence pulse simultaneously transmitted by the DS2761 and any other slaves on the bus. The presence pulse tells the bus master that one or more devices are on the bus and ready to operate. For more details, see the 1-Wire Signaling section. NET ADDRESS COMMANDS Once the bus master has detected the presence of one or more slaves, it can issue one of the net address commands described in the following paragraphs. The name of each ROM command is followed by the 8-bit opcode for that command in square brackets. Figure 16 presents a transaction flowchart of the net address commands. Read Net Address [33h or 39h]. This command allows the bus master to read the DS2761's 1-Wire net address. This command can only be used if there is a single slave on the bus. If more than one slave is present, a data collision occurs when all slaves try to transmit at the same time (open drain produces a wired-AND result). The RNAOP bit in the status register selects the opcode for this command, with RNAOP = 0 indicating 33h, and RNAOP = 1 indicating 39h. Match Net Address [55h]. This command allows the bus master to specifically address one DS2761 on the 1-Wire bus. Only the addressed DS2761 responds to any subsequent function command. All other slave devices ignore the function command and wait for a reset pulse. This command can be used with one or more slave devices on the bus. Skip Net Address [CCh]. This command saves time when there is only one DS2761 on the bus by allowing the bus master to issue a function command without specifying the address of the slave. If more than one slave device is present on the bus, a subsequent function command can cause a data collision when all slaves transmit data at the same time. Search Net Address [F0h]. This command allows the bus master to use a process of elimination to identify the 1-Wire net addresses of all slave devices on the bus. The search process involves the repetition of a simple three-step routine: read a bit, read the complement of the bit, then write the desired value of that bit. The bus master performs this simple three-step routine on each bit location of the net address. After one complete pass through all 64 bits, the bus master knows the address of one device. The remaining devices can then be identified on additional iterations of the process. See Chapter 5 of the Book of DS19xx iButton(R) Standards for a comprehensive discussion of a net address search, including an actual example. (This publication can be found on the Maxim/Dallas Semiconductor website at www.maximic.com). 16 of 24 DS2761 SWAP [AAh]. SWAP is a ROM level command specifically intended to aid in distributed multiplexing applications and is described specifically with regards to power control using the 27xx series of products. The term power control refers to the ability of the DS2761 to control the flow of power into or out the battery pack using control pins DC and CC . The SWAP command is issued followed by the net address. The effect is to cause the addressed device to enable power to or from the system while simultaneously (break-before-make) deselecting and powering down (SLEEP) all other packs. This switching sequence is controlled by a timing pulse issued on the DQ line following the net address. The falling edge of the pulse is used to disable power with the rising edge enabling power flow by the selected device. The DS2761 recognizes a SWAP command, device address, and timing pulse only if the SWEN bit is set. FUNCTION COMMANDS After successfully completing one of the net address commands, the bus master can access the features of the DS2761 with any of the function commands described in the following paragraphs and summarized in Table 4. The name of each function is followed by the 8-bit opcode for that command in square brackets. Read Data [69h, XX]. This command reads data from the DS2761 starting at memory address XX. The LSb of the data in address XX is available to be read immediately after the MSb of the address has been entered. Because the address is automatically incremented after the MSb of each byte is received, the LSb of the data at address XX + 1 is available to be read immediately after the MSb of the data at address XX. If the bus master continues to read beyond address FFh, the DS2761 outputs logic 1 until a reset pulse occurs. Addresses labeled "Reserved" in the memory map contain undefined data. The read data command can be terminated by the bus master with a reset pulse at any bit boundary. Write Data [6Ch, XX]. This command writes data to the DS2761 starting at memory address XX. The LSb of the data to be stored at address XX can be written immediately after the MSb of address has been entered. Because the address is automatically incremented after the MSb of each byte is written, the LSb to be stored at address XX + 1 can be written immediately after the MSb to be stored at address XX. If the bus master continues to write beyond address FFh, the DS2761 ignores the data. Writes to read-only addresses, reserved addresses and locked EEPROM blocks are ignored. Incomplete bytes are not written. Writes to unlocked EEPROM blocks are to shadow RAM rather than EEPROM. See the Memory section for more details. Copy Data [48h, XX]. This command copies the contents of shadow RAM to EEPROM for the 16-byte EEPROM block containing address XX. Copy data commands that address locked blocks are ignored. While the copy data command is executing, the EEC bit in the EEPROM register is set to 1 and writes to EEPROM addresses are ignored. Reads and writes to non-EEPROM addresses can still occur while the copy is in progress. The copy data command execution time, tEEC, is 2ms typical and starts after the last address bit is transmitted. Recall Data [B8h, XX]. This command recalls the contents of the 16-byte EEPROM block containing address XX to shadow RAM. Lock [6Ah, XX]. This command locks (write-protects) the 16-byte block of EEPROM memory containing memory address XX. The LOCK bit in the EEPROM register must be set to l before the lock command is executed. If the LOCK bit is 0, the lock command has no effect. The lock command is permanent; a locked block can never be written again. 17 of 24 DS2761 Table 4. FUNCTION COMMANDS COMMAND Read Data Write Data Copy Data Recall Data Lock DESCRIPTION Reads data from memory starting at address XX Writes data to memory starting at address XX Copies shadow RAM data to EEPROM block containing address XX Recalls EEPROM block containing address XX to shadow RAM Permanently locks the block of EEPROM containing address XX COMMAND PROTOCOL 69h, XX 6Ch, XX 48h, XX B8h, XX 6Ah, XX BUS STATE AFTER COMMAND PROTOCOL Master Rx Master Tx Bus idle Bus idle Bus idle BUS DATA Up to 256 bytes of data Up to 256 bytes of data None None None 18 of 24 DS2761 Figure 16. NET ADDRESS COMMAND FLOW CHART MASTER Tx RESET PULSE DS2761 Tx PRESENCE PULSE MASTER Tx NET ADDRESS COMMAND 33h / 39h READ NO 55h MATCH NO F0h SEARCH NO AAh SWAP NO CCh SKIP NO YES DS2761 Tx FAMILY CODE 1 BYTE YES MASTER Tx BIT 0 YES DS2761 Tx BIT 0 DS2761 Tx BIT 0 MASTER Tx BIT 0 YES MASTER Tx BIT 0 YES MASTER Tx FUNCTION COMMAND DS2761 Tx SERIAL NUMBER 6 BYTES BIT 0 MATCH ? DS2761 Tx CRC 1 BYTE NO NO BIT 0 MATCH ? NO BIT 0 MATCH ? YES MASTER Tx BIT 1 YES DS2761 Tx BIT 1 DS2761 Tx BIT 1 MASTER Tx BIT 1 YES MASTER Tx BIT 1 BIT 1 MATCH ? NO NO BIT 1 MATCH ? NO BIT 1 MATCH ? YES YES YES MASTER Tx BIT 63 DS2761 Tx BIT 63 DS2761 Tx BIT 63 MASTER Tx BIT 63 MASTER Tx BIT 63 MASTER Tx FUNCTION COMMAND YES BIT 63 MATCH ? NO BIT 63 MATCH ? YES NO FALLING EDGE OF DQ RISING EDGE OF DQ DS2761 TO SLEEP MODE DS2761 TO ACTIVE MODE 19 of 24 DS2761 I/O SIGNALING The 1-Wire bus requires strict signaling protocols to insure data integrity. The four protocols used by the DS2761 are as follows: the initialization sequence (reset pulse followed by presence pulse), write 0, write 1, and read data. All of these types of signaling except the presence pulse are initiated by the bus master. The initialization sequence required to begin any communication with the DS2761 is shown in Figure 17. A presence pulse following a reset pulse indicates that the DS2761 is ready to accept a net address command. The bus master transmits (Tx) a reset pulse for tRSTL. The bus master then releases the line and goes into receive mode (Rx). The 1-Wire bus line is then pulled high by the pullup resistor. After detecting the rising edge on the DQ pin, the DS2761 waits for tPDH and then transmits the presence pulse for tPDL. Figure 17. 1-WIRE INITIALIZATION SEQUENCE tRSTL tPDH DQ PACKLINE TYPE LEGEND: BUS MASTER ACTIVE LOW BOTH BUS MASTER AND DS2761 ACTIVE LOW DS2761 ACTIVE LOW RESISTOR PULLUP tRSTH tPDL PACK+ WRITE-TIME SLOTS A write-time slot is initiated when the bus master pulls the 1-Wire bus from a logic-high (inactive) level to a logic-low level. There are two types of write-time slots: write 1 and write 0. All write-time slots must be tSLOT (60ms to 120ms) in duration with a 1ms minimum recovery time, tREC, between cycles. The DS2761 samples the 1-Wire bus line between 15ms and 60ms after the line falls. If the line is high when sampled, a write 1 occurs. If the line is low when sampled, a write 0 occurs (see Figure 18). For the bus master to generate a write 1 time slot, the bus line must be pulled low and then released, allowing the line to be pulled high within 15ms after the start of the write time slot. For the host to generate a write 0 time slot, the bus line must be pulled low and held low for the duration of the write-time slot. READ-TIME SLOTS A read-time slot is initiated when the bus master pulls the 1-Wire bus line from a logic-high level to a logic-low level. The bus master must keep the bus line low for at least 1ms and then release it to allow the DS2761 to present valid data. The bus master can then sample the data tRDV (15ms) from the start of the read-time slot. By the end of the read-time slot, the DS2761 releases the bus line and allows it to be pulled high by the external pullup resistor. All read-time slots must be tSLOT (60ms to 120ms) in duration with a 1ms minimum recovery time, tREC, between cycles. See Figure 18 for more information. 20 of 24 DS2761 Figure 18. 1-WIRE WRITE- AND READ-TIME SLOTS WRITE 0 SLOT WRITE 1 SLOT tSLOT tLOW0 tREC DQ tLOW1 tSLOT PACK+ PACK- DS2761 SAMPLE WINDOW MIN TYP MAX 15ms 15ms 30ms >1ms 15ms DS2761 SAMPLE WINDOW MIN TYP MAX 15ms 30ms READ 0 SLOT READ 1 SLOT tSLOT tREC tSLOT PACK+ DQ PACK- MASTER SAMPLE WINDOW >1ms MASTER SAMPLE WINDOW tRDV LINE TYPE LEGEND: BUS MASTER ACTIVE LOW BOTH BUS MASTER AND DS2761 ACTIVE LOW tRDV DS2761 ACTIVE LOW RESISTOR PULLUP Figure 19. SWAP COMMAND TIMING tSWL DQ tSWOFF CC , DC tSWON CC , DC 21 of 24 DS2761 ABSOLUTE MAXIMUM RATINGS* Voltage on PLS and CC Pin, Relative to VSS Voltage on PIO Pin, Relative to VSS Voltage on VIN and PS, Relative to VSS Voltage on any Other Pin, Relative to VSS Continuous Internal Sense Resistor Current Pulsed Internal Sense Resistor Current Operating Temperature Range Storage Temperature Range Soldering Temperature -0.3V to +18V -0.3V to +12V -0.3V to VDD + 0.3 -0.3V to +6V 2.5A 50A for <100s/sec, <1000 pulses -40C to +85C -55C to +125C See IPC/JEDECJ-STD-020A * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS PARAMETER Supply Voltage Data Pin PARAMETER Active Current Sleep Mode Current Input Logic High: DQ, PIO Input Logic High: PS Input Logic Low: DQ, PIO Input Logic Low: PS Output Logic High: CC Output Logic High: DC Output Logic Low: CC , DC Output Logic Low: DQ, PIO DQ Pulldown Current Input Resistance: VIN Internal Current-Sense Resistor DQ Low to Sleep time SYMBOL VDD DQ CONDITIONS (-20C to +70C, 2.5V VDD 5.5V) MIN 2.5 -0.3 TYP MAX 5.5 +5.5 UNITS V V NOTES 1 1 DC ELECTRICAL CHARACTERISTICS SYMBOL CONDITIONS IACTIVE DQ = VDD, norm. operation ISLEEP DQ = 0V, no activity, PS floating VIH VIH VIL VIL VOH VOH VOL VOL IPD RIN RSNS tSLEEP 22 of 24 MIN (-20C to +70C, 2.5V VDD 5.5V) TYP 60 1 1.5 MAX 90 2 UNITS mA mA NOTES V V 0.4 0.2 V V V V 0.4 0.4 1 V V mA MW mW 1 1 1 1 1 1 1 1 VDD 0.2V IOH = -0.1mA IOH = -0.1mA IOL = 0.1mA IOL = 4mA VPLS 0.4V VDD 0.4V +25C 5 20 2.1 25 30 s DS2761 ELECTRICAL CHARACTERISTICS: PROTECTION CIRCUITRY PARAMETER Overvoltage Detect Charge Enable Undervoltage Detect Overcurrent Detect Overcurrent Detect Short-Circuit Detect Short-Circuit Detect Overvoltage Delay Undervoltage Delay Overcurrent Delay Short-Circuit Delay Test Threshold Test Current Recovery Charge Current SYMBOL VOV VCE VUV IOC VOC ISC VSC tOVD tUVD tOCD tSCD VTP ITST IRC MIN 4.325 4.250 4.10 2.5 1.8 45 5.0 150 0.8 90 5 80 0.5 10 0.5 TYP 4.350 4.275 4.15 2.6 1.9 47.5 8.0 200 1 100 10 100 1.0 20 1 (0C to +50C, 2.5V VDD 5.5V) MAX 4.375 4.300 4.20 2.7 2.0 50 11 250 1.2 110 20 120 1.5 40 2 UNITS V V V A mV A mV sec ms ms ms NOTES 1, 2 1 1 3 1, 4 3 1 V mA mA 13 ELECTRICAL CHARACTERISTICS: TEMPERATURE, VOLTAGE, CURRENT PARAMETER Temperature Resolution Temperature Full-Scale Magnitude Temperature Error Voltage Resolution Voltage Full-Scale Magnitude Voltage Offset Error Voltage Gain Error Current Resolution Current Full-Scale Magnitude Current Offset Error Current Gain Error Accumulated Current Resolution Current Sampling Frequency Internal Timebase Accuracy SYMBOL TLSB TFS TERR VLSB VFS VOERR VGERR ILSB IFS IOERR IGERR qCA fSAMP tERR 1.9 MIN 127 (-20C to +50C, 2.5V VDD 5.5V) TYP 0.125 MAX UNITS C C C mV V NOTES 4.88 4.75 3 5 1 5 0.625 15.625 2.56 64 1 3 1 0.25 6.25 1456 1 3 LSB % mA A mV LSB % mAhr Vhr Hz % mV 6 3 4 3, 4 7 8 3, 9 4 3 4 10 23 of 24 DS2761 ELECTRICAL CHARACTERISTICS: 1-WIRE INTERFACE PARAMETER Time Slot Recovery Time Write 0 Low Time Write 1 Low Time Read Data Valid Reset Time High Reset Time Low Presence Detect High Presence Detect Low SWAP Timing Pulse Width SWAP Timing Pulse Falling Edge to DC Release SWAP Timing Pulse Rising Edge to DC Engage DQ Capacitance SYMBOL tSLOT tREC tLOW0 tLOW1 tRDV tRSTH tRSTL tPDH tPDL tSWL tSWOFF tSWON CDQ MIN 60 1 60 1 480 480 15 60 0.2 0 0 (-20C to +70C, 2.5V VDD 5.5V) TYP MAX 120 120 15 15 960 60 240 120 1 1 60 UNITS ms ms ms ms ms ms ms ms ms ms ms ms NOTES 12 12 pF EEPROM RELIABILITY SPECIFICATION PARAMETER Copy to EEPROM Time EEPROM Copy Endurance SYMBOL tEEC NEEC MIN 25000 (-20C to +70C, 2.5V VDD 5.5V) TYP 2 MAX 10 UNITS ms cycles NOTES 11 NOTES 1) 2) 3) 4) 5) All voltages are referenced to VSS. See the Ordering Information section to determine the corresponding part number for each VOV value. Internal current-sense resistor configuration. External current-sense resistor configuration. Self-heating due to output pin loading and sense resistor power dissipation can alter the reading from ambient conditions. 6) Voltage offset measurement is with respect to VOV at +25C. 7) The current register supports measurement magnitudes up to 2.56A using the internal sense resistor option and 64mV with the external resistor option. Compensation of the internal sense resistor value for process and temperature variation can reduce the maximum reportable magnitude to 1.9A. 8) Current offset error null to 1LSB typically requires 3.5s in-system calibration by user. 9) Current gain error specification applies to gain error in converting the voltage difference at IS1 and IS2, and excludes any error remaining after the DS2761 compensates for the internal sense resistor's temperature coefficient of 3700ppm/C to an accuracy of 500ppm/C. The DS2761 does not compensate for external sense resistor characteristics, and any error terms arising from the use of an external sense resistor should be taken into account when calculating total current measurement error. 10) Typical value for tERR is at 3.6V and +25C. 11) Four year data retention at +70C. 12) Typical load capacitance on DC and CC is 1000pF. 13) Test conditions are PLS = 4.1V, VDD = 2.5V. Maximum current for conditions of PLS = 15V, VDD = 0V is 10mA. 24 of 24 |
Price & Availability of DS2761
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |